Portable Audio Cassette Adapter.
Allows the audio of any portable device with a 1/8" (3.5mm)
stereo headphone jack to play through a car stereo cassette
system. Adapter cable plugs into the portable player stereo
headphone jack and the adapter inserts into the cassette
player like a standard cassette tape.
Perfect for use with MP3 and CD players, portable video and
DVD players, and any other portable device with a stereo
headphone jack. Can even be used with laptop computers
with headphone/speaker output jacks.
(Stock #: AUTOACC01)
CD / DVD Laser Lens Cleaner.
Keeps optical laser lens clean and dust free.
Disc also includes an Audio System Check.
For use with CD and DVD players/recorders.
With storage case.
Note: Not for use with X-Box or any other gaming system.
(Stock #: AUD04)
Phonograph Speed Strobe Disc.
Phonograph Speed Strobe Disc is permanently
laser engraved with markings that are smudge,
water, and scratch resistant. Disc is constructed
from break-resistant Polycarbonate Plastic.
Strobe Disc is calibrated for the following phonograph speeds:
16 2/3 RPM - 33 1/3 RPM - 45 RPM - 78 RPM
For use under 60 Hz. fluorescence, neon, or incandescent lighting.
4 3/4" diameter. With protective case and instructions.
Reel-To-Reel Recording Tape.
Good quality polyester base recording tape.
5 inch reel. 900 feet x 1.0 mil.
(Stock #: AUD02)
Reel-To-Reel 5 inch reel.
Good quality heavy plastic reel.
(Stock #: AUD03)
Micro Cassette Recording Tape.
Good quality polyester base tape.
C60 leaderless. 30 minutes per side.
Also can be used with micro cassette
telephone answerers as an incoming tape.
With storage case.
(Stock #: AUD01)
High Power 2-Way Speaker Crossover Network.
Rated at 100 Watts. For 4 or 8 ohm speakers.
3000 Hz. crossover frequency. 12 dB/octave cut-off rate.
Solderless spring-clip connections.
For home or automotive use.
Size: 5 3/16" x 3 7/16" x 2".
(Stock #: AUD05)
High Power Speaker Choke Coil.
High linearity and low distortion 4.25 mH. choke
has less than 1 Ohm DC resistance. Rated at
200 Watts max. 150 Hz. cutoff at 4 Ohms,
300 Hz. cutoff at 8 Ohms. Perfect for
high-power crossover networks.
(Stock #: SPCHK)
Audio Dummy Load Power Resistor.
Rated at 8 Ohm 250 Watt 5%.
Non-inductive at audio frequencies.
Hollow cylindrical design allows the use
of a fan for forced-air cooling.
Solder/screw lug terminals.
Size: 12" x 1 1/8" diameter.
Ohmite part number: 270-251P-46.
(Stock #: AUDRES01)
Data Sheet - PDF File size: 538K
6 Ohm T-Pad Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. 0-36 dB attenuation. Wirewound
elements, 3 sections, industrial grade. T-Pads are used
to control audio levels in audio circuits where constant
impedance between input and output must be maintained.
Size (less shaft and terminals): 2" x 1 5/8" diameter.
Shaft size: 2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware and wiring diagram.
Mallory part number: T-6.
(Stock #: AUDPAD04)
Data Sheet - PDF File size: 538K
16 Ohm T-Pad Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. 0-38 dB attenuation. Wirewound
elements, 3 sections, industrial grade. T-Pads are used
to control audio levels in audio circuits where constant
impedance between input (amplifier) and output (speaker)
must be maintained.
Size (less shaft and terminals): 2 1/4" x 3/4" diameter.
Shaft size: 1/2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware, face plate, and wiring diagram.
Mallory part number: MRT16.
(Stock #: AUDPAD01)
Data Sheet - PDF File size: 538K
200 Ohm T-Pad Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. 0-38 dB attenuation. Wirewound
elements, 3 sections, industrial grade. T-Pads are used
to control audio levels in audio circuits where constant
impedance between input and output must be maintained.
Size (less shaft and terminals): 2" x 1 5/8" diameter.
Shaft size: 2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware and wiring diagram.
Mallory part number: T-200.
(Stock #: AUDPAD05)
Data Sheet - PDF File size: 538K
3,000 Ohm T-Pad Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. 0-38 dB attenuation. Wirewound
elements, 3 sections, industrial grade. T-Pads are used
to control audio levels in audio circuits where constant
impedance between input and output must be maintained.
Size (less shaft and terminals): 2" x 1 5/8" diameter.
Shaft size: 2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware and wiring diagram.
Mallory part number: T3000.
(Stock #: AUDPAD02)
Data Sheet - PDF File size: 538K
200 Ohm L-Pad Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. 0-38 dB attenuation. Wirewound
elements, 2 sections, industrial grade. L-Pads are used
to control audio levels in audio circuits where constant
impedance is maintained only to the input.
Size (less shaft and terminals): 1 1/2" x 1 5/8" diameter.
Shaft size: 2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware, face plate, and wiring diagram.
Mallory part number: L200.
(Stock #: AUDPAD06)
Data Sheet - PDF File size: 538K
16 Ohm Stereo L-Pad Attenuator.
Each channel is rated at 15 Watts average audio power.
4 Watts DC maximum. 0-38 dB attenuation. Wirewound
elements, 4 sections, industrial grade. L-Pads are used
to control audio levels in audio circuits where constant
impedance is maintained only to the input (amplifier).
Size (less shaft and terminals): 2 3/4" x 3/4" diameter.
Shaft size: 1/2" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware, knob, face plate, and wiring diagram.
Mallory part number: MRLL16.
(Stock #: AUDPAD07)
Data Sheet - PDF File size: 538K
4 Ohm Stereo Balance Attenuator.
Rated at 15 Watts average audio power.
4 Watts DC maximum. Wirewound elements,
4 sections, industrial grade. Used to control
the balance of 2 audio channels, as the shaft
is turned, one channel increases while the
other decreases. Constant impedance is
maintained to the input.
Size (less shaft and terminals): 3 1/4" x 1 5/8" diameter.
Shaft size: 7/16" x 1/4" diameter. Mounts in a 3/8" hole.
With mounting hardware, face plate, and wiring diagram.
Mallory part number: BAL 4.
-Click Here To Return To Parts Index-
-Click Here To Return To Main Page-